显示屏体系统设计技术参数一 、屏体技术参数 PH10-1R1G1B-三

显示屏体系统设计技术参数
一 、屏体技术参数
PH10-1R1G1B-三合一贴片全彩-8扫-恒流柔性屏
1.1像素点结构图
A：结构示意图


结构说明：每像素点采用1红1绿1蓝三合一表贴发光管
灯管封装为：SMD3528
B： 专业分析
分析项目 专业分析内容
配色分析 为使配色达到最佳的白平衡效果，配色对LED 发光的亮度有严格要求，其中红绿蓝色亮度的配色比例为 R：G ：B=3：6：1
1.2 像素点指标
灯管颜色 指 标（典型值，具体与所选灯有关）
R(红) 波长：620~625nm，亮度250~350mcd
G(绿) 波长：525~530nm，亮度600~700mcd
B(蓝) 波长：465~470nm，亮度100~150mcd
1.3技术参数
名 称 技术参数
1、像素管 像素点间距：10mm
晶片产地：红色晶片: 晶元
绿色+蓝色晶片: 士兰
基色：红色+绿色+蓝色
发光点颜色组合：1R1G1B
物理密度：10000点/m2
2、单元板 单元板分辨率：宽32点×高16点
单元板尺寸: 320mm×160mm
单元板像素数：512点/单元板
单元板材质：柔性PCB板+硬板（FPC+FR-4）
3、显示屏整屏 屏体显示面积：㎡
单元板数量：块
物理分辨率：
视角: 140°
存贮温度： -40℃ ～ +85℃
工作温度：-10℃ ～ +50℃
相对湿度：10%～95%
4、供电 工作电压： 220V±15％
平均功耗： 300W/m2
最大功耗： 600W/m2
5、控制系统 控制主机：联想开天主机或同档次计算机以上
操作系统：WIN 98/ 2000/ XP
控制方式：同步控制
显卡：DVI显卡
6、主要技术参数 1） 驱动器件：恒流
2）驱动方式：8扫
3）刷新频率：≥300Hz
4）帧频： ≥60Hz
5）灰度/颜色：4K/显示16.7M颜色
6）亮度：≥800cd/m2
7）亮度调节方式：软件256级可调
8）视频信号：RF、S-Video、RGB、RGBHV、YUV、YC、COMPOSITION等
9）控制系统采用：PCTV卡（可选）＋DVI显卡＋主控卡＋光纤传输（可选）
10）平均无故障时间：1000小时
11）寿命：10万小时
12）平整度：任意相邻像素间≤0.5mm；
单元板拼接间隙＜1mm ；
13）均匀性：像素光强、单元板亮度均匀
14）杂点率：＜0.0001
15）开关电源负荷：5V/40A、5V/30A
16）计算机显示模式：1280×1024
17）有效通讯距离：网线100m（无中继）,多模光纤500m，单模光纤20km

結果 (英文) 1:

Display body system design parameters
Panel technical ph10-1r1g1b-three-in-one SMD full color -8 sweep - constant current flexible screen
1.1 pixel point diagram
a: Schematic diagram of


Structure Description The lamp package: each pixel with 1 red and 1 green, 1 blue triple paste emitting tube
: smd3528
b: professional analysis
professional analysis of the content of the analysis project
color for color to achieve the best balance effect brightness of the color of the led luminous stringent requirements, including the color of red, green and blue brightness ratio of r: g: b = 3:6:1
1.2 pixel point indicators
lamp color indicators (typical value, specifically with the selected lamp related)
r (red) wavelength: 620 to 625nm, brightness 250 ~ 350mcd
g (green) wavelength: 525 to 530 nm, 600 ~ 700mcd brightness
b (blue) wavelength: 465 to 470 nm, brightness of the technical parameters of 100 ~ 150mcd
1.3
Name technical parameters
1 pixel pipe pixel pitch: 10mm
chip Origin: red chip: Epistar
green blue chip: Swaziland
primary colors: red green blue
luminous point color combinations: 1r1g1b
Physical density: 10000 points / m2
2, unit board Module resolution: 32 wide x high 16:00
unit board size: 320mm x 160mm
cell plate number of pixels: 512 points / unit board
the unit board material:Flexible pcb board hard board (fpc fr-4)
3, the entire screen of the display screen body area: m
number of unit board: block
physical resolution:
Viewing angle: 140 °
Storage Temperature: -40 ℃ ~ 85 ℃
Operating Temperature: -10 ℃ to 50 ℃
Relative Humidity: 10% to 95%
4, the power supply voltage: 220v ± 15%
average power consumption: 300w/m2 maximum power consumption: 600w/m2
5 control system to control the host: Lenovo Kaitian host or above the same level of computer
operating system: win 98/2000 / xp
control mode: synchronous control
graphics: dvi graphics
6, the main technical parameters 1) to drive the device: constant current
2) driven by:Sweep
3) Refresh Rate: ≥ 300hz
4) frame rate: ≥ 60hz
5) grayscale / color: 4k / of 16.7m colors
6) Brightness: ≥ 800cd/m2
7) Brightness adjustment: Software 256 level adjustable
8) video signal: rf, s-video, rgb, rgbhv, yuv, yc, composition
9) control system using: pctv card (optional) + dvi video card + main control card + fiber transmission (optional )
10) mean time to failure: 1000 hours
11) the flatness of Life: 100,000 hours
12): any adjacent pixels ≤ 0.5mm;
unit board stitching gap <1mm;
13) uniformity: pixel light strong, uniform brightness of the cell plate
14) noise rate: <0.0001
15) switching power supply load: 5v/40a ​​5v/30a
16) computer display mode: 1280 x 1024
17) effective communication distance: network cable 100m (without relay), multi-mode Fibre 500m, single mode fiber 20km

結果 (英文) 2:

Display system design parameters on one screen, technical parameters
PH10-1R1G1B- three in one patch full-color -8 scan - constant flow of flexible screen
1.1 pixel structure graph
A: Structure: Structure: each pixel with 1 red and 1 green 1 blue three in a SMD LED lamp package: SMD3528
B:
professional analysis
analysis program analysis content analysis in order to achieve
color matching optimum white balance effect, color matching on LED luminous brightness are strict requirements, in which red and green blue brightness color ratio of R:G:B=3:6:1
1.2 pixel lamp indicator
color index (typical, specific and selected lights on)
R (red) wavelength: 620~625nm, the brightness of 250~350mcd
G (green) wavelength: 525~530nm, the brightness of 600~700mcd
B (blue) wavelength: 465~470nm, the brightness of 100~150mcd
1.3 technical parameters
name technical parameters
1, pixel tubes pixel interval: 10mm
wafer origin: red chip: crystal element
green blue chip: Kingsland
color: red green blue
luminous point color combinations: 1R1G1B
physical density: 10000 /m2
2, unit plate unit board resolution: 32 x 16 bit width
unit board size: 320mm × 160mm
unit board like prime number: 512 / unit plate
unit plate material:Flexible PCB boards made of (FPC FR-4)
3, display the whole screen body display area: m
unit plate number: block physical resolution:

perspective: 140 °
storage temperature: -40 ℃ ~ 85 ℃
working temperature: -10 ℃ ~ 50 ℃ and relative humidity: 10% ～ 95%
4, the power supply voltage: average power consumption of 220V ± 15%
: 300W/m2
: 600W/m2
5, maximum power control system control host: Associate host or same grade computer above the operating system: WIN 98/ 2000/
XP
control modes: synchronous control
video card: DVI
6 graphics, the main technical parameters 1) driving device: constant current
2 driver):8
3 refresh frequency sweep): ≥ 300Hz
4) frame: ≥ 60Hz
5) gray / color: color 4K/ display 16.7M
6) ≥ 800cd/m2
7): brightness brightness adjustment: software 256 stage adjustable
8) video signal: RF, S-Video, RGB, RGBHV, YUV, YC, COMPOSITION,
9) control system using: PCTV card (optional) + DVI + main control card and optical fiber transmission (optional)
10) mean time to failure: 1000 hours
11) life: 100000 hours
12): any smoothness between adjacent pixels ≤ 0.5mm;
unit plate splicing gap < 1mm;
13) uniformity: pixel intensity, unit board brightness uniformity.14) miscellaneous points rate: < 0.0001
15) switching power supply load: 5V/40A, 5V/30A
16) of computer display mode: 1280 × 1024
17) effective communication distance: Line 100m (no relay), 500m 20km
multimode fiber, single-mode fiber

結果 (英文) 3:

Display body system design technology parameter
a, and screen body technology parameter
PH10-1R1G1B-three-in-one posted tablets full color-8 sweep-constant flow flexible screen
1.1 pixel points structure figure
A: structure diagram


structure Description: each pixel points used 1 red 1 green 1 blue three-in-one table posted glow tube
lamp package for: SMD3528
B: professional analysis
analysis project professional analysis content
color scheme analysis for makes color scheme reached best of white balance effect, color scheme on LED glow of brightness has strict, Brightness of the red, green and blue color scheme for R:G:B=3:6:1
1.2 pixel index
lamp color indicators (typical value, associated with the selected lamp)
R (red) wavelength: 620~625nm, intensity 250~350mcd
G (green) wavelength: 525~530nm, intensity 600~700mcd
B (blue) wavelength: 465~470nm, bright 100~150mcd
1.3 technology parameter technology parameter
1, pixel pixel
name space: 10MM
chip origin: red chips: wafer
green blue chips: SILAN
-color: red green blue
Dots color combinations: 1R1G1B
physical density: 10,000/m2
2, unit plate element Board resolution: 32 wide x 16
unit panel size: 320mmx160mm
unit of pixels: 512-point/cell
cell material:Flexible PCB Board-like consistency (FPC FR-4)
3, displays the entire screen screen display area: SQM
unit number:
physical resolution:
angle: 140 ° storage temperature
:
~85 ℃-40 ℃ operating temperature:-10 ° c
~50 ℃ relative humidity: 10%~95%
4, power supply operating voltage: 220V ± 15%
average power consumption: 300W/m2
max power consumption: 600W/m2
5, control system Control hosts: above
Lenovo host open days or same grade computer operating system: WIN 98/2000/XP
control: synchronous control
video: 1 DVI video card
6, main technical parameter) drive:
2 constant current) drive:8 scan
3) refresh rate: ≥ 300Hz
4) frame rate: ≥ 60Hz
5) grayscale/color: 4K/16.7M color
6) brightness: ≥ 800cd/m2
7) brightness adjustment: software, 256-level adjustable
8) video signal: RF, s-video, and RGB, and RGBHV, YUV, and YC, COMPOSITION etc
9) control system uses: PCTV card (optional) +DVI video card + master card + optical fiber transmission (optional)
10) average time between failures:
11 1000 hours) life: 100,000 hours
12) flatness: splicing gap between any adjacent pixels less than 0.5mm;
cell <1mm;
13) uniformity: pixel light intensity, range of uniform brightness
14) noise rate: <0.0001
15) switching power supply load: 5V/40A, and 5V/30A
16) computer display mode: 1280x1024
17) effective communication distance: network cable 100m (Repeater), multimode optical fiber 500m, single mode fiber 20km