本工程道路的机动车道上单项双车道，小型车道车道宽度为3. 75米，大型

本工程道路的机动车道上单项双车道，小型车道车道宽度为3. 75米，大型车道车道宽度为3.75米；非机动车道宽度单侧为5米；人行道宽度为5米。
(1)交通标线的作用是管制和引导交通，包括路面标线、突起路标和立面标记等。
(2)交通标线按以下情况设置。
①路面标线形式有车行道中心线，车行道边缘线、车道分界线、停止线、人行横道线、减速让行线、导流标线、平面交叉口中心圈、车行道宽度渐变段标线、停车位标线、停靠站标线、出入口标线、导向箭头以及路面文字或图形标记等。
a纵向标线
车行道分界线为长2.0米，间隔4米的白色虚线。车行道边缘线为白色实线。在有出入口路段的道路中心用长2.0米，间隔4米的中心黄色虚实线分隔。无出入口路段的道路中心用中心黄色双实线分隔。所有的纵向标线的线宽均为15cm。
b横向标线
人行横道线设置在交叉路口处，其设计长度为5米，线宽40cm，线与线之间的间隔为60cm。
c其他标线
路面文字标记、导向箭头线及其他标线的设计尺寸样式详见图。
②突起路标是固定于路面上突起的标记块，应做成定向反射型。一般路段反光玻璃珠为白色，危险路段为红色或黄色。
③立面标记可设在跨线桥、渡槽等的墩柱或侧墙端面上以及隧道洞口和安全岛等的壁面上。交通标线的设置原则及具体作法应符合《道路交通标志和标线》（GB 5768-2009）的规定。

結果 (英文) 1:

This project single two-lane on the motorway the road, small lanes lane width is 3. 75 metres, large lane lane width 3.75 m; bicycle lane width is 5 m; sidewalk width is 5 m.(1) traffic marking function is to control and direct traffic, including pavement marking, raised pavement markers and elevation marking.(2) traffic lines according to the following settings.① pavement marking center line of the roadway, roadway edges, lane dividing lines, crosswalks, stop line lines, slow lines, guide lines, intersection of center circle, transition section of roadway width marking, parking marking, stop marking, import text or graphics lines, guiding arrows and pavement marking.A longitudinal markingRoadway demarcation for 2.0 m long, 4 m intervals, white dashed lines. Roadway edge are white solid lines. In the different sections of the road in the Centre with a 2.0 m long, 4 m intervals of yellow dash from the center lane. Free entrance road in the Centre of the road separated by a double solid yellow line away from the Center. All the vertical reticle line width of 15cm.B horizontal road marking Zebra set intersection, its length is 5 meters, width 40cm, interval between the line and the line 60cm.C additional markingPavement mark text, guiding the arrow line and other lines of the design dimension styles see figure.II raised pavement markers are fixed on the raised markings on the pavement blocks, should make the directional reflection type. General section of reflective glass beads are white, dangerous sections of red or yellow.③ façade marks can be set in the flyover, aqueducts, such as the pillar or wall end face and tunnel entrance and pedestrian refuges on the wall. Traffic lines and setting principles and practices should be consistent with the road signs and marking (GB 5768-2009) regulations.

結果 (英文) 2:

The motor vehicle lane of single two-lane road project, a small lane lane width of 3.75 m, a large driveway lane width of 3.75 m; width unilateral non-motorized vehicles 5 meters; sidewalk width of 5 meters.
(1) the role of traffic markings are regulated and guided transport, including road markings, signs and projections facade markings.
(2) traffic markings by the following settings.
① pavement marking in the form of roadway centerline roadway edge lines, lane dividing line, stop line, crosswalk, slowdown and yield line, diversion marking, center ring Intersection, roadway width Transition Section marking, parking marking, marking stops, marking the entrance, the guide arrow and pavement markings text or graphics.
a longitudinal marking
roadway dividing line is 2.0 meters long, spaced 4 meters white dotted line. Roadway edge line of solid white line. In the entrance there are sections of the center of the road, separated by 2.0 m long, spaced 4 meters center yellow broken line. No entrance section of the center of the road separated by yellow double solid center line. All longitudinal marking width are 15cm.
b transverse marking
crosswalk lines are set at the intersection, which is designed length of 5 meters, the interval width 40cm, between the lines is 60cm.
c other marking
pavement marking text, the guide arrows and other markings design dimension style see FIG.
② protruding signs are fixed to the pavement marker block projection, orientation should be made reflective. General road reflective glass beads as a white, red or yellow dangerous sections.
③ elevation tag can be located in a flyover, the aqueduct and other wall pier or the end surface of the side wall and the tunnel entrance and refuges, etc. on. Setting principles traffic markings and specific practices should follow the "road traffic signs and markings" (GB 5768-2009) regulations.

結果 (英文) 3:

The road of the project on the motor vehicle lanes, small lanes width of 3.75 meters, the width of the large lane 3.75 meters; non motorized lane width of 5 meters; sidewalk width of 5 meters.(1) traffic marking is the role of control and guide traffic, including road marking, labeling and elevation road signs.(2) the traffic marking set according to the following.The pavement marking form of roadway centerline, the roadway edge line, lane line, stop line, crossing, slow line, central guide markings, intersection ring, roadway width of transition marking, parking marking, stop marking, exit marking, guide arrow and road marking text or graphics.Longitudinal marking aThe lane dividing line is 2 meters long, 4 meters interval white dotted line. The roadway edge line for solid white line. In the entrance section of the road center with a length of 2 meters, 4 meters apart from the center of the yellow line separation. No entrance section of the road center center yellow double solid line separator. Longitudinal marking all the line width is 15cm.B horizontal lineThe crossing is set in the intersection, the design length of 5 meters, width of 40cm, between the line and the line spacing is 60cm.C other markingsThe size of design style, see Figure pavement text markup oriented arrow lines and other markings.The raised road sign is a marker which is fixed on the road surface, and it should be made into a directional reflection type. General sections of reflective glass beads for white, dangerous sections of red or yellow.The pier or side walls of the end mark may be located in the flyover, aqueduct on the tunnel entrance and the safety island and on the wall. Setting principles and specific methods of traffic marking shall be in accordance with the "road traffic signs and markings" (GB 5768-2009) regulations.